View TC7660H_70980.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EVALUATION KIT AVAILABLE
TC7660H
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER
FEATURES
s s s s s s s Pin Compatible with 7660, High Frequency Performance DC-to-DC Converter Low Cost, Two Low Value External Capacitors Required ........................................................ (1.0F) Converts +5V Logic Supply to 5V System Wide Input Voltage Range .................... 1.5V to 10V Voltage Conversion ........................................ 99.7% Power Efficiency ................................................ 85% Available in 8-Pin SOIC and 8-Pin PDIP Packages
GENERAL DESCRIPTION
The TC7660H is a pin-compatible, high frequency upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +10V input to a corresponding - 1.5V to - 10V output using only two lowcost capacitors, eliminating inductors and their associated cost, size and EMI. The TC7660H operates at a frequency of 120kHz (versus 10kHz for the TC7660), allowing the use of 1.0F external capacitors. Oscillator frequency can be reduced (for lower supply current applications) by connecting an external capacitor from OSC to ground. The TC7660H is available in 8-pin DIP and small outline (SOIC) packages in commercial and extended temperature ranges.
PIN CONFIGURATION (DIP and SOIC)
NC 1 8 V+
CAP + 2 GND 3 TC7660HCPA TC7660HEPA
7 OSC 6 LOW VOLTAGE (LV) 5 VOUT
ORDERING INFORMATION
Part No.
TC7660HCOA TC7660HCPA TC7660HEOA TC7660HEPA TC7660EV
CAP - 4
Package
8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC
Temperature Range
0C to +70C 0C to +70C - 40C to +85C
NC CAP + GND CAP -
1 2 3 4 TC7660HCOA TC7660HEOA
8 7 6 5
V+ OSC LOW VOLTAGE (LV) VOUT
8-Pin Plastic DIP - 40C to +85C Evaluation Kit for Charge Pump Family
NC = NO INTERNAL CONNECTION
FUNCTIONAL BLOCK DIAGRAM
V + CAP + 8 2
OSC
7
RC OSCILLATOR
/2
VOLTAGE- LEVEL TRANSLATOR
4
CAP -
LV
6 5 INTERNAL VOLTAGE REGULATOR LOGIC NETWORK VOUT
TC7660H
3 GND
(c) 2001 Microchip Technology Inc. DS21466A
TC7660H-2 10/1/96
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage ...................................................... +10.5V LV and OSC Inputs Voltage (Note 1) ........................ - 0.3V to (V+ + 0.3V) for V+ < 5.5V + - 5.5V) to (V+ + 0.3V) (V for V+ > 5.5V Current Into LV (Note 1) ..................... 20A for V+ > 3.5V Output Short Duration (VSUPPLY 5.5V) ......... Continuous Power Dissipation (TA 70C) (Note 2) SOIC ...............................................................470mW Plastic DIP ......................................................730mW Operating Temperature Range C Suffix .................................................. 0C to +70C E Suffix ............................................ - 40C to +85C Storage Temperature Range ............... - 65C to +150C Lead Temperature (Soldering, 10 sec) ................. +300C
*Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS: Over Operating Temperature Range with V+= 5V, CI = C2 = 1F, COSC = 0,
Test Circuit (Figure 1), unless otherwise indicated. Symbol
I+
+ VH + VL
Parameter
Supply Current Supply Voltage Range, High Supply Voltage Range, Low Output Source Resistance
Test Conditions
RL = Min TA Max, RL = 5k, LV Open Min TA Max, RL = 5k, LV to GND IOUT = 20mA, TA = 25C IOUT = 20mA, 0C TA +70C (C Device) IOUT = 20mA, - 40C TA +85C (E Device) V+ = 2V, IOUT = 3mA, LV to GND 0C TA +70C IOUT = 10mA, Min TA Max RL =
Min
-- 3 1.5 -- -- -- -- -- 81 99
Typ
0.46 -- -- 55 -- -- 150 120 85 99.7
Max
1.0 10 3.5 80 95 110 250 -- -- --
Unit
mA V V kHz % %
ROUT
FOSC PEFF VEFF
Oscillator Frequency Power Efficiency Voltage Efficiency
NOTES: 1. Connecting any input terminal to voltages greater than V+ or less than GND may cause destructive latch-up. It is recommended that no inputs from sources operating from external supplies be applied prior to "power up" of the TC7660H. 2. Derate linearly above 50C by 5.5mW/C.
TC7660H-2 10/1/96
2
(c) 2001 Microchip Technology Inc.
DS21466A
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
To improve low-voltage operation, the LV pin should be connected to GND. For supply voltages greater than 3.5V, the LV terminal must be left open to ensure latch-upproof operation and prevent device damage.
V+ (+5V)
IS 1 2 C1 1.0 F + 3 4 8 7
Theoretical Power Efficiency Considerations
In theory, a capacitative charge pump can approach 100% efficiency if certain conditions are met: (1) The drive circuitry consumes minimal power. (2) The output switches have extremely low ON resistance and virtually no offset.
TC7660H
6 5
+
C2 1.0 F
RL
(3) The impedances of the pump and reservoir capacitors are negligible at the pump frequency. The TC7660H approaches these conditions for negative voltage multiplication if large values of C1 and C2 are used. Energy is lost only in the transfer of charge between capacitors if a change in voltage occurs. The energy lost is defined by: E = 1/2 C1 (V12 - V22) V1 and V2 are the voltages on C1 during the pump and transfer cycles. If the impedances of C1 and C2 are relatively high at the pump frequency (refer to Figure 1), compared to the value of RL, there will be a substantial difference in voltages V1 and V2. Therefore, it is not only desirable to make C2 as large as possible to eliminate output voltage ripple, but also to employ a correspondingly large value for C1 in order to achieve maximum efficiency of operation.
Figure 1. TC7660H Test Circuit
Detailed Description
The TC7660H contains all the necessary circuitry to implement a voltage inverter, with the exception of two external capacitors, which may be inexpensive 1.0F non-polarized capacitors. Operation is best understood by considering Figure 2, which shows an idealized voltage inverter. Capacitor C1 is charged to a voltage, V+, for the half cycle when switches S1 and S3 are closed. (Note: Switches S2 and S4 are open during this half cycle.) During the second half cycle of operation, switches S2 and S4 are closed, with S1 and S3 open, thereby shifting capacitor C1 negatively by V+ volts. Charge is then transferred from C1 to C2, such that the voltage on C2 is exactly V+, assuming ideal switches and no load on C2.
Do's and Don'ts
* Do not exceed maximum supply voltages. * Do not connect LV terminal to GND for supply voltages greater than 3.5V.
V+
S1
S2
* Do not short circuit the output to V+ supply for voltages above 5.5V for extended periods; however, transient conditions including start-up are okay.
C2 VOUT = - VIN
GND
S3
S4
* When using polarized capacitors in the inverting mode, the + terminal of C1 must be connected to pin 2 of the TC7660H and the + terminal of C2 must be connected to GND Pin 3.
Figure 2. Idealized Charge Pump Inverter
(c) 2001 Microchip Technology Inc. DS21466A
3
TC7660H-2 10/1/96
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
Simple Negative Voltage Converter
Figure 3 shows typical connections to provide a negative supply where a positive supply is available. A similar scheme may be employed for supply voltages anywhere in the operating range of +1.5V to +10V, keeping in mind that pin 6 (LV) is tied to the supply negative (GND) only for supply voltages below 3.5V. The output characteristics of the circuit in Figure 3 are those of a nearly ideal voltage source in series with 70. Thus, for a load current of - 10 mA and a supply voltage of +5V, the output voltage would be - 4.3V. The dynamic output impedance of the TC7660H is due, primarily, to capacitive reactance of the charge transfer capacitor (C1). Since this capacitor is connected to the output for only 1/2 of the cycle, the equation is: 2 XC = = 2.12, 2f C1 where f = 150kHz and C1 = 1.0F. ROUT =
V+ 1 2 1.0 F + 3 4 8 7 1 2 1.0 F + 3 4 8 7
1 C1 1.0 F + 2 3 4 8 7 VOUT* C2 1.0 F V+
TC7660H
6 5 V+ 10V
+
* NOTES:
1. VOUT = -n V+ for 1.5V
Figure 3. Simple Negative Converter
Paralleling Devices
Any number of TC7660H voltage converters may be paralleled to reduce output resistance (Figure 4). The reservoir capacitor, C2, serves all devices, while each device requires its own pump capacitor, C1. The resultant output resistance would be approximately: ROUT (of TC7660H) n (number of devices)
TC7660H
"1"
6 5
TC7660H
"n"
6 5 + VOUT* 1.0 F
* NOTES:
1. VOUT = -n V + for 1.5V
V+
10V
Figure 4. Increased Output Voltage by Cascading Devices
Cascading Devices
The TC7660H may be cascaded as shown in (Figure 4) to produce larger negative multiplication of the initial supply voltage. However, due to the finite efficiency of each device, the practical limit is probably 10 devices for light loads. The output voltage is defined by: VOUT = - n (VIN) where n is an integer representing the number of devices cascaded. The resulting output resistance would be approximately the weighted sum of the individual TC7660H ROUT values.
TC7660H-2 10/1/96
Changing the TC7660H Oscillator Frequency
It may be desirable in some applications (due to noise or other considerations) to increase or decease the oscillator frequency. This can be achieved by overdriving the oscillator from an external clock, as shown in Figure 6. In order to prevent possible device latch-up, a 1k resistor must be used in series with the clock output. In a situation where the designer has generated the external clock frequency using TTL logic, the addition of a 10k pull-up resistor to V+ supply is required. Note that the pump frequency with external clocking, as with internal clocking, will be 1/2 of the clock frequency. Output transitions occur on the positive-going edge of the clock.
4
(c) 2001 Microchip Technology Inc. DS21466A
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
V 1 2 C1 3 4 8 7 1 2 C1 3 4 8 7 RL +
TC7660H
"1"
6 5
TC7660H
"n"
6 5 RL + C2
Figure 5. Paralleling Devices Lowers Output Impedance
V+ 1 2 1.0 F + 3 4 8 1 k 7 CMOS GATE V+
Combined Negative Voltage Conversion and Positive Supply Multiplication
Figure 8 combines the functions shown in Figures 3 and 8 to provide negative voltage conversion and positive voltage multiplication simultaneously. This approach would be, for example, suitable for generating +9V and -5V from an existing +5V supply. In this instance, capacitors C1 and C3 perform the pump and reservoir functions, respectively, for the generation of the negative voltage, while capacitors C2 and C4 are pump and reservoir, respectively, for the multiplied positive voltage. There is a penalty in this configuration which combines both functions, however, in that the source impedances of the generated supplies will be somewhat higher due to the finite impedance of the common charge pump driver at pin 2 of the device.
TC7660H
6 5 + VOUT 1.0 F
Figure 6. External Clocking
Positive Voltage Multiplication
The TC7660H may be employed to achieve positive voltage multiplication using the circuit shown in Figure 7. In this application, the pump inverter switches of the TC7660H are used to charge C1 to a voltage level of V+ - VF (where V+ is the supply voltage and VF is the forward voltage drop of diode D1). On the transfer cycle, the voltage on C1 plus the supply voltage (V+) is applied through diode D2 to capacitor C2. The voltage thus created on C2 becomes (2 V+) - (2 VF), or twice the supply voltage minus the combined forward voltage drops of diodes D1 and D2. The source impedance of the output (VOUT) will depend on the output current, but for V+ = 5V and an output current of 10mA, it will be approximately 60.
V+ 1 2 3 4 8 7 D1 D2 + C1 + C2 VOUT = (2 V+) - (2 VF)
V+ 1 2 3 + C1 4 + C2 8 7 +
VOUT = - (V+- VF) C3
TC7660H
6 5
D1
D2
VOUT = (2 V +) - (2 VF) + C4
TC7660H
6 5
Figure 7. Positive Voltage Multiplier
(c) 2001 Microchip Technology Inc. DS21466A
Figure 8. Combined Negative Converter and Positive Multiplier 5
TC7660H-2 10/1/96
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
Efficient Positive Voltage Multiplication/ Conversion
Since the switches that allow the charge pumping operation are bidirectional, the charge transfer can be performed backwards as easily as forwards. Figure 9 shows a TC7660H transforming -5V to +5V (or +5V to +10V, etc.). The only problem here is that the internal clock and switchdrive section will not operate until some positive voltage has been generated. An initial inefficient pump, as shown in Figure 9, could be used to start this circuit up, after which it will bypass the diode and resistor shown dotted in Figure 9.
1 2 C1 1.0 F + 3 4 8 7 1 M VOUT = -V-
+
1.0 F
TC7660H
6 5 V- INPUT
Figure 9. Positive Voltage Conversion
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 1)
Output Source Resistance vs. Supply Voltage
10k
Output Source Resistance vs. Temperature
500
OUTPUT SOURCE RESISTANCE ()
OUTPUT SOURCE RESISTANCE ()
TA = +25C
IOUT = 1 mA 450 400 200 150 V + = +2V 100 50 V + = +5V
1k
100
10 0 1 2 3 4 5 6 SUPPLY VOLTAGE (V) 7 8
0 -55
-25
0 +25 +50 +75 +100 +125 TEMPERATURE (C)
Output Voltage vs. Output Current CI C2 =1F
0 -1 5 4 3
Output Voltage vs. Load Current
TA = +25C V+ = +5V
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
TA = +25C LV OPEN 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA)
-2 -3 -4 -5 -6 -7 -8 -9 -10
2 1 0 -1 -2 -3 -4 -5 0 10 20 30 40 50 60 70 LOAD CURRENT (mA) 80 SLOPE 55
TC7660H-2 10/1/96
6
(c) 2001 Microchip Technology Inc.
DS21466A
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
PACKAGE DIMENSIONS 8-Pin Plastic DIP
PIN 1
.260 (6.60) .240 (6.10)
.045 (1.14) .030 (0.76) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92)
.070 (1.78) .040 (1.02)
.310 (7.87) .290 (7.37)
.040 (1.02) .020 (0.51)
.015 (0.38) .008 (0.20) .400 (10.16) .310 (7.87)
3 MIN.
.110 (2.79) .090 (2.29)
.022 (0.56) .015 (0.38)
8-Pin SOIC
.157 (3.99) .150 (3.81) .244 (6.20) .228 (5.79)
.050 (1.27) TYP.
.197 (5.00) .189 (4.80) .069 (1.75) .053 (1.35) .020 (0.51) .010 (0.25) .013 (0.33) .004 (0.10) .010 (0.25) .007 (0.18) .050 (1.27) .016 (0.40)
Dimensions: inches (mm)
8 MAX.
(c) 2001 Microchip Technology Inc.
DS21466A
7
TC7660H-2 10/1/96
HIGH FREQUENCY 7660 DC-TO-DC VOLTAGE CONVERTER TC7660H
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com
New York
150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335
ASIA/PACIFIC (continued)
Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850
San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955
Rocky Mountain
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456
Taiwan
Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Toronto
6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509
Atlanta
500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
ASIA/PACIFIC
China - Beijing
Microchip Technology Beijing Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104
Austin
Analog Product Sales 8303 MoPac Expressway North Suite A-201 Austin, TX 78759 Tel: 512-345-2030 Fax: 512-345-6085
EUROPE
Australia
Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755
Boston
2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821
China - Shanghai
Microchip Technology Shanghai Office Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060
Denmark
Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910
Boston
Analog Product Sales Unit A-8-1 Millbrook Tarry Condominium 97 Lowell Road Concord, MA 01742 Tel: 978-371-6400 Fax: 978-371-0050
France
Arizona Microchip Technology SARL Parc diActivite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Hong Kong
Microchip Asia Pacific RM 2101, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431
Chicago
333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924
India
Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, OiShaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062
Germany
Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Dayton
Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175
Germany
Analog Product Sales Lochhamer Strasse 13 D-82152 Martinsried, Germany Tel: 49-89-895650-0 Fax: 49-89-895650-22
Detroit
Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260
Japan
Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Italy
Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883
Los Angeles
18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934
United Kingdom
Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 Printed on recycled paper.
01/09/01
Mountain View
Analog Product Sales 1300 Terra Bella Avenue Mountain View, CA 94043-1836 Tel: 650-968-9241 Fax: 650-967-1590
All rights reserved. (c) 2001 Microchip Technology Incorporated. Printed in the USA. 1/01
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchipis products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
TC7660H-2 10/1/96
8
(c) 2001 Microchip Technology Inc.
DS21466A

▲Up To Search▲

Price & Availability of TC7660H

	To Download TC7660H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .